| 1. |
|
|
| 2. |
- Gadisa, Abay, et al.
(författare)
-
Improvements of fill factor in solar cells based on blends of polyfluorene copolymers as electron donors
- 2007
-
Ingår i: Thin Solid Films. - : Elsevier BV. - 0040-6090 .- 1879-2731. ; 515:5, s. 3126-3131
-
Tidskriftsartikel (refereegranskat)abstract
- The photovoltaic characteristics of solar cells based on alternating polyfluorene copolymers, poly(2,7-(9,9-dioctyl-fluorene)-alt-5,5-(4′,7′-di-2-thienyl-2′,1′,3′-benzothiadiazole)) (APFO-3), and poly(2,7-(9,9-didodecyl-fluorene)-alt-5,5-(4′,7′-di-2-thienyl-2′,1′,3′-benzothiadiazole)) (APFO-4), blended with an electron acceptor fullerene molecule [6,6]-phenyl-C61-butyric acid methyl ester (PCBM), have been investigated and compared. The two copolymers have the same aromatic backbone structure but differ by the length of their alkyl side chain. The overall photovoltaic performance of the solar cells is comparable irrespective of the copolymer used in the active layer. However, the fill factor (FF) values of the devices are strongly affected by the copolymer type. Higher FF values were realized in solar cells with APFO-4 (with longer alkyl side chain)/PCBM bulk heterojunction active layer. On the other hand, devices with blends of APFO-3/APFO-4/PCBM were found to render fill factor values that are intermediate between the values obtained in solar cells with APFO-3/PCBM and APFO-4/PCBM active film. Upon using APFO-3/APFO-4 blends as electron donors, the cell efficiency can be enhanced by about 16% as compared to cells with either APFO-3 or APFO-4. The transport of holes in each polymer obeys the model of hopping transport in disordered media. However, the degree of energetic barrier against hopping was found to be larger in APFO-3. The tuning of the photovoltaic parameters will be discussed based on studies of hole transport in the pure polymer films, and morphology of blend layers. The effect of bipolar transport in PCBM will also be discussed.
|
|
| 3. |
- Zhang, Fengling, et al.
(författare)
-
Influence of solvent mixing on the morphology and performance of solar cells based on polyfluorene copolymer/fullerene blends
- 2006
-
Ingår i: Advanced Functional Materials. - : Wiley. - 1616-3028 .- 1616-301X. ; 16:5, s. 667-674
-
Tidskriftsartikel (refereegranskat)abstract
- The influence of the solvent on the morphol. and performance of polymer solar cells was studied in devices based on blends of the polyfluorene copolymer, poly(2,7-(9,9-dioctyl-fluorene)-alt-5,5-(4',7'-di-2-thienyl-2', 1',3'-benzothiadiazole)), and [6,6]-phenyl-C61-butyric acid Me ester. The blends are spin-coated from CHCl3 or from CHCl3 mixed with small amts. of xylene, toluene, or chlorobenzene. The devices are characterized under monochromatic light and AM1.5 solar illumination. An enhancement of the photocurrent d. was obsd. in diodes made from CHCl3 mixed with chlorobenzene, and a decreased photocurrent d. is obsd. in diodes made from CHCl3 mixed with xylene or toluene, compared to diodes made from neat CHCl3. The open-circuit voltages are almost the same for all diodes. The surfaces of the active layers were imaged with AFM. Height images indicate that a finer and more uniform distribution of domains corresponds to the diodes with enhanced photocurrent that are made from CHCl3 mixed with chlorobenzene, while a structure with larger domains is assocd. with the lower photocurrents in the diodes made from CHCl3 mixed with xylene or toluene. The influence of the morphol. on the excited-state dynamics and charge generation was studied using time-resolved spectroscopy. Fast formation of bound charge pairs followed by their conversion into free charge carriers was resolved, and excitation-intensity-dependent non-geminate recombination of free charges was obsd. A significant enhancement in free-charge-carrier generation was obsd. on introducing chlorobenzene into CHCl3. Imaging photocurrent generation from the solar cells with a light-pulse technique shows an inhomogeneous photocurrent distribution, which is related to the undulations in the thickness of the active layer. Thicker parts of the diodes yield higher photocurrent values. [on SciFinder (R)]
|
|
| 4. |
|
|
